丁二酸酐酯化改性糯米淀粉的研究

目的 为了提高糯米淀粉的粘度，以达到标签胶的要求。方法 对糯米淀粉进行丁二酸酐酯化改性，通过单因素试验及响应面优化确定出最佳酯化条件，测定其理化性质，并对其进行结构表征。结果 丁二酸酐酯化改性糯米淀粉的最优工艺条件：丁二酸酐添加量（丁二酸酐占淀粉干基的质量百分比）为10.3%，酯化温度为41.5℃，酯化时间为2.0 h,pH为9.0，在此条件下制得的糯米淀粉胶的粘度较高，可达到61.6 Pa·s，且溶解性与溶胀度均有不同程度的提高。电镜与热力学性质分析表明，酯化后淀粉颗粒结晶结构受到破坏，表面粗糙，出现凹陷与裂缝。结论 经过丁二酸酐酯化后，糯米淀粉胶的粘度得到提高。     

Magnetic properties,phase evolution,hollow structure and biomedical application of hematite (α-Fe2O3) and QUAIPH

We investigate synthesis, phase evolution, hollow and porous structure and magnetic properties of quasi-amorphous intermediate phase (QUAIPH) and hematite (α-Fe₂O₃) nanostructure synthesized by annealing of akaganeite (β-FeOOH) nanorods. It is found that the annealing temperature determines the phase composition of the products, the crystal structure/size dictates the magnetic properties whereas the final nanorod morphology is determined by the starting material. Annealing of β-FeOOH at ～300 °C resulted in the formation of hollow QUAIPH nanorods. The synthesized material shows low-cytotoxicity, superparamagnetism and good transverse relaxivity, which is rarely reported for QUAIPH. The QUAIPH nanorods started to transform to porous hematite nanostructures at ～350 °C and phase transformation was completed at 600 °C. During the annealing, the crystal structure changed from monoclinic (akaganeite) to quasi-amorphous and rhombohedral (hematite). Unusually, the crystallite size first decreased (akaganeite → QUAIPH) and then increased (QUAIPH → hematite) during annealing whereas the nanorods retained particle shape. The magnetic properties of the samples changed from antiferromagnetic (akaganeite) to superparamagnetic with blocking temperature T_B = 84 K (QUAIPH) and finally to weak-ferromagnetic with the Morin transition at T_M = 244 K and high coercivity H_C = 1652 Oe (hematite). The low-cytotoxicity and MRI relaxivity (r₂ = 5.80 mM^?1 s^?1 (akaganeite), r₂ = 4.31 mM^?1 s^?1 (QUAIPH) and r₂ = 5.17 mM^?1 s^?1 (hematite)) reveal potential for biomedical applications.     

Controlled growth of Bi-Functional La doped CeO2 nanorods for photocatalytic H2 production and supercapacitor applications

The rapid increase in energy consumption has severely rehabilitated human life urging to develop reliable and environmental friendly energy storage devices. Target oriented, systematic approach has been adopted to synthesis La doped CeO₂ nanostructures with percentage as La_xCe_1-xO₂ (X = 0,1,3,5,7) for potential super capacitors applications. Morphological doping impact on H₂ production, electrochemical and optical properties are thoroughly investigated. XRD studies revealed the crystalline phase purity and attained approximately 35 nm average crystallite size. The SEM images exposed that primary morphology nano-particles has been tuned into nanorods by increasing the La concentration in CeO₂ with size range 40～60 nm. CV graphs depicted that the prepared electrodes obey the pseudo capacitive faradaic reactions behavior in nature. Maximum capacitance (925 F g^-1) has been achieved by La_0·05Ce_0·95O₂ which is better than numerous reported materials. The La_0·05Ce_0·95O₂ also exhibited excellent GCD stability with 87.8% retention exhibiting it suitability for supercapacitor applications. Furthermore, the La_0·05Ce_0·95O₂ showed the significantly higher H₂ (9 μmol h^?1g^?1) production rate as compared to undoped CeO₂ and La_0·01Ce_0·99O_2, La_0·03Ce_0·97O₂ samples. This higher production is attributed to the recombination rate and have strong substantial correlation with optical characteristics.     

Novel one- and two-dimensional InSbS3 semiconductors for photocatalytic water splitting: The role of edge electron states

Photocatalytic water splitting has become a promising technology to solve environmental pollution and energy shortage. Exploring stable and efficient photocatalysts are highly desired. Herein, we propose novel low-dimensional InSbS₃ semiconductors with good stability based on density functional theory. Such InSbS₃ structures could be obtained from their bulk crystal by suitable exfoliation methods. Our calculations indicate that two-dimensional (2D) and one-dimensional (1D) InSbS₃ nanostructures have moderate band gaps (2.54 and 1.97 eV, respectively) and suitable band edge alignments, which represents sufficient redox capacity for photocatalytic water splitting. 2D InSbS₃ monolayer possesses oxygen evolution reaction (OER) activity and 1D InSbS₃ single-nanochain possesses hydrogen evolution reaction (HER) activity under acidic conditions. Interestingly, two edge electron states can be introduced when the dimension of InSbS₃ is reduced from 2D to 1D and the new electron states can exist in arbitrary-width nanoribbons, which can effectively promote the process of HER. Moreover, InSbS₃ monolayer and single-nanochain also exhibit large solar-to-hydrogen efficiency, high carrier mobility, and excellent optical absorption properties, which can facilitate the process of photocatalytic reactions. Our findings can stimulate the synthesis and applications of low-dimensional InSbS₃ semiconductors for overall water splitting.     

Double emulsion (W/O/W) gel stabilised by polyglycerol polyricinoleate and calcium caseinate as mangiferin carrier: insights on formulation and stability properties

Mangiferin (MGF) is a phenolic compound isolated from mango, but its poor solubility significantly limits its use. In this study, MGF was embedded into the inner aqueous phase of W₁/O/W₂ emulsions. Firstly, the dissolution method of MGF was determined. MGF remained stable in solution with pH 13 at 30 min, and its solubility reached 10 mg mL⁻¹. When the pH of MGF solutions was adjusted from pH 13 to pH 6, MGF did not immediately crystallise, providing sufficient time to construct the MGF-loaded W₁/O/W₂ emulsions. Subsequently, the MGF-loaded W₁/O/W₂ emulsions were constructed using polyglycerol polyricinoleate (PGPR) and calcium caseinate (CAS). The formation and stability of the W₁/O/W₂ emulsions were investigated. The MGF-loaded W₁/O/W₂ emulsions stabilised with 1% PGPR and 1% – 3% CAS exhibited a low viscosity, limited loading capacity, and poor stability. Conversely, the MGF-loaded W₁/O/W₂ emulsions stabilised by 3%PGPR–3%CAS exhibited optimal loading capacity (encapsulation efficiency = 95.31% and loading efficiency = 0.91%) and stability, which was attributed to the fact that high viscosity and gel state retarded the migration of inner aqueous phase. These results indicated that the W₁/O/W₂ emulsions stabilised by PGPR and CAS may be a potential alternative for encapsulating mangiferin.     

Feasibility of high performance in p-type Ge1−xBixTe materials for thermoelectric modules

GeTe is a promising candidate for the fabrication of high-temperature segments for p-type thermoelectric (TE) legs. The main restriction for the widespread use of this material in TE devices is high carrier concentration (up to ∼ 10²¹ cm⁻³), which causes the low Seebeck coefficient and high electronic component of thermal conductivity. In this work, the band structure diagram and phase equilibria data have been effectively used to attune the carrier concentration and to obtain the high TE performance. The Ge_1−xBi_xTe (x = 0.04) material prepared by the Spark plasma sintering (SPS) technique demonstrates a high power factor accompanied by moderate thermal conductivity. As a result, a significantly higher dimensionless TE figure of merit ZT = 2.0 has been obtained at ∼ 800 K. Moreover, we are the first to propose that application of the developed Ge_1−xBi_xTe (x = 0.04) material in the TE unicouple should be accompanied by SnTe and CoGe₂ transition layers. Only such a unique solution for the TE unicouple makes it possible to prevent the negative effects of high contact resistance and chemical diffusion between the segments at high temperatures.     

Tetragonal tungsten bronze phase potential in increasing the piezoelectricity of sol-gel synthesized (K0.5Na0.5)1-xLixNbO3 ceramics

(K,Na)NbO₃ (KNN)-based ceramics have been proven to be formidable candidates among lead-free piezoelectric materials, yet poor reproducibility always hinders their progress. In the present study, the effects of low lithium substitution on the electrical properties and microstructure of (K_0.5Na_0.5)_1-xLi_xNbO₃ (KNLN) ceramics were investigated. All samples were synthesized by the sol-gel method. The Curie temperature (T_C) of the ceramics shifted to higher temperature and gradually decreased the monoclinic-tetragonal (T_M-T) phase transition. Li⁺ substitution had a prominent effect on the ferroelectric properties and improved the piezoelectric coefficient (d₃₃) up to 181 pC/N. X-Ray Diffraction (XRD) studies and Field Emission Scanning Electron Microscopy (FESEM) images revealed an inevitable tetragonal tungsten bronze (TTB) secondary phase, which was formed during the preparation process. It was demonstrated that the volatilization of Li⁺ cations facilitated TTB growth. The coexistence of two different phase structures proved to enhance the KNN piezoelectric performance.     

Bovidae-based gelatin: Extractions method,physicochemical and functional properties,applications, and future trends

Gelatin is one of the most important multifunctional biopolymers and is widely used as an essential ingredient in food, pharmaceutical, and cosmetics. Porcine gelatin is regarded as the leading source of gelatin globally then followed by bovine gelatin. Porcine sources are favored over other sources since they are less expensive. However, porcine gelatin is religiously prohibited to be consumed by Muslims and the Jewish community. It is predicted that the global demand for gelatin will increase significantly in the future. Therefore, a sustainable source of gelatin with efficient production and free of disease transmission must be developed. The highest quality of Bovidae-based gelatin (BG) was acquired through alkaline pretreatment, which displayed excellent physicochemical and rheological properties. The utilization of mammalian- and plant-based enzyme significantly increased the gelatin yield. The emulsifying and foaming properties of BG also showed good stability when incorporated into food and pharmaceutical products. Manipulation of extraction conditions has enabled the development of custom-made gelatin with desired properties. This review highlighted the various modifications of extraction and processing methods to improve the physicochemical and functional properties of Bovidae-based gelatin. An in-depth analysis of the crucial stage of collagen breakdown is also discussed, which involved acid, alkaline, and enzyme pretreatment, respectively. In addition, the unique characteristics and primary qualities of BG including protein content, amphoteric property, gel strength, emulsifying and viscosity properties, and foaming ability were presented. Finally, the applications and prospects of BG as the preferred gelatin source globally were outlined.     

Influence of high energy ball milling on structural,microstructural and optical properties of TiO2 nanoparticles

The influence of high-energy ball milling on structural, microstructural, and optical properties of TiO₂ by modifying the nanoparticle size was studied. Five samples were extracted at different milling times (0, 2, 4, 8, and 13 h). The average particle sizes estimated by dynamic light scattering (DLS) were 205, 155.8, 116.8, 82.9, and 82.7 nm at 0, 2, 4, 8, and 13 h, respectively. X-ray diffraction analysis confirmed progressive broadening of the peaks as the milling time elapsed. Besides, a correlation was found between d spacing and the average crystal size. The UV–Vis diffuse reflectance spectra of TiO₂ revealed a decrease in reflectance due to particle size reduction. Similarly, an alteration of the bandgap transition energy was presented, whose values gradually decreased from 2.966 eV to 2.861 eV for the sample without and with the maximum duration milling performed (13 h), respectively. Likewise, the SEM analysis showed a distribution in nanoparticle size that became more homogeneous and smaller average grain size as the milling duration was longer.